Audio · M4A to MP3

M4A to MP3 converter, batch and local.

Drop in up to ten .m4a files, such as iPhone voice memos or music exports, and get MP3s back at the bitrate you pick. The conversion happens in this tab and the files are never uploaded.

Batch of 10CBR or VBRNo upload

Why people convert M4A to MP3

An M4A file is audio stored in an MP4 container, usually AAC, sometimes Apple Lossless. It plays well on Apple devices and most phones, but plenty of older car stereos, dictation software, podcast hosts and video editors still ask for MP3. That is the whole job here: take the M4A, decode it, and write a standard MP3 that anything can open.

The most common source is a batch of voice memos from an iPhone or Mac: interviews, lectures, meetings, a song idea. They arrive as .m4a, you need MP3, and you would rather not hand a private recording to a website that uploads it to a server. This converter keeps the file on your device: the browser reads it, a WebAssembly build of FFmpeg decodes it, the LAME encoder writes the MP3, and you download the result.

Choosing settings for voice versus music

Speech needs far less data than music. For a spoken recording, 64 to 96 kbps in mono is usually enough to understand every word, and a one-hour memo at 64 kbps comes to about 28.8 MB (64,000 bits per second ÷ 8 × 3,600 seconds). The same hour at 128 kbps is 57.6 MB, and at 320 kbps it is 144 MB. For music, start at 192 kbps or use VBR.

Constant bitrate (CBR) spends the same number of bits every second, which gives predictable file sizes. Variable bitrate (VBR) lets the encoder spend more on complex passages and less on silence; the LAME quality scale runs from V0 (highest quality) to V9 (lowest). Because the actual bitrate depends on the audio, the result card shows the size you really got.

The sample rate normally stays as it is. If the source rate is one MP3 cannot store, the tool moves it to the nearest legal rate and the options list the choices: 48, 44.1, 32, 22.05 and 16 kHz. A bitrate that is too high for a low sample rate is lowered automatically; at 22.05 kHz the MP3 format tops out at 160 kbps.

Worked example

You have a 25-minute lecture recorded in Voice Memos. Choose CBR, 96 kbps, channels set to mono, and press Convert. Expect an MP3 of roughly 18 MB (96,000 ÷ 8 × 1,500 s = 18,000,000 bytes). Play it in the card to check it, then download. If the file is only for transcription software, drop to 64 kbps and the size falls to about 12 MB.

What gets lost, and what does not

Converting M4A (AAC) to MP3 is lossy to lossy: the audio is decoded and then compressed a second time with a different method. Each generation adds a little distortion, so keep your M4A originals and use the MP3 as a copy. If the M4A is Apple Lossless (the Voice Memos “Lossless” setting), you are starting from a perfect copy and the loss happens once.

Title, artist and similar tags can be carried over as ID3v2.3 tags (the checkbox is on by default). Embedded cover art is not copied. The MP3 can come out a few hundredths of a second longer than the M4A, because MP3 stores audio in fixed-size frames and the encoder pads the end.

Limits and common mistakes

Privacy: what the code does

The converter lives in an isolated frame on this page. That frame has no network access and does not load advertising or analytics, so there is nowhere for your audio to go. The files are read into memory with the browser’s file API, converted by FFmpeg running as WebAssembly in the same tab, and returned as downloads from your own device. Nothing is stored after you close the page. The ads on this page sit outside the frame and cannot see your files.

Common mix-ups

  1. RFC 4337: MIME Type Registration for MPEG-4
  2. MDN: Web audio codec guide

Checked against these sources on .

Frequently asked questions

Can I convert iPhone voice memos to MP3 here?

Yes. Voice Memos are normally saved as .m4a files, which this page accepts. Share or save them to Files, choose them here, and download the MP3s. Nothing is uploaded.

Does the converter work with Apple Lossless M4A files?

Yes. The engine decodes both AAC and Apple Lossless (ALAC) inside .m4a files. The tool reports which codec it found next to each result.

What bitrate should I choose for a voice recording?

Between 64 and 96 kbps is normally enough for speech, especially in mono. Use 128 kbps if you want some headroom, and 192 kbps or more for music.

Why is my MP3 not much smaller than the M4A?

AAC and MP3 are both compressed formats and AAC is the more efficient one. At the same bitrate the files are nearly the same size. To get a smaller MP3, choose a lower bitrate or mono.

Will the MP3 sound worse than the M4A?

Slightly, in principle. Going from one lossy format to another compresses the audio twice. At 128 kbps and above most listeners will not hear it on speech, but keep the original M4A.

Are cover art and tags kept?

Text tags such as title and artist are copied as ID3v2.3 when the tags box is ticked. Embedded cover art is not copied to the MP3.

Is there a file size or count limit?

Up to 10 files per run and 300 MB per file. Files outside those limits are skipped with a message while the others continue.

Why does a file say no audio stream was found?

The file is damaged, is not really audio, or is protected. Try opening it in a media player first; a DRM-locked .m4p purchase cannot be converted.

Sources

Standards and documentation behind the claims on this page.

What this tool does not do

It does not remove DRM from protected purchases, repair damaged recordings, copy cover art, or make the audio better than the M4A it came from. Lossy formats (MP3, AAC, Ogg) discard information, so keep your originals.

Advertisement
Advertisement