Audio · AAC to MP3

AAC to MP3 converter for raw .aac files.

Open the .aac files that many players refuse, whether they are bare AAC streams or AAC inside an .m4a, and save them as MP3. Bitrate, VBR and channel options, ten files per run, no upload.

.aac and .m4aBatch of 10No upload

A .aac file is not an .m4a file

AAC (Advanced Audio Coding) is a compression method. It can be stored in two common ways. Inside an MP4-family container the file is named .m4a (or .m4b for audiobooks), and it has a header with the duration, tags and an index for seeking. As a bare stream of ADTS frames it is named .aac. A raw .aac file has no such header: it is just frames, one after another, each with its own small header that carries the sample rate and channel count.

That difference explains the odd behaviour of .aac files. Some players do not know how long they are until they have read the whole file, many media libraries ignore them and some tools refuse the extension outright. MP3 avoids all of that. This page converts the bare .aac stream and also accepts AAC in .m4a or audio-only .mp4, since people often call both “AAC”. For files you know are voice memos or purchases, the M4A to MP3 converter has the same engine with M4A-specific notes.

Where raw .aac files come from

You are most likely to meet them as recordings from handheld recorders and some phones, internet radio and stream captures, audio extracted from video by various tools, and exports from older software. They are lossy, typically 64 to 256 kbps. Converting to MP3 compresses them a second time, so it is a compatibility step rather than a quality step: keep the original .aac as your master.

Settings

The default is constant 160 kbps. The result card shows the source rate, channel count and the bitrate when the file reports one. Pick an MP3 bitrate at or above the source bitrate so the second round of compression has room. Speech sources can drop to 64 or 96 kbps in mono. You can also choose variable bitrate (V0 highest to V9 lowest on the LAME scale) if you want size to follow the complexity of the audio.

The sample rate stays as the stream says, mapped to the nearest rate MP3 can store if needed (AAC allows rates such as 88.2 kHz that MP3 does not). A bitrate too high for a low sample rate is lowered automatically. Tags are rarely present in a bare ADTS file; the Keep tags box applies to .m4a input.

Worked example

A radio capture is a 30-minute file of 44.1 kHz stereo AAC at 128 kbps, which is 28.8 MB. You want a copy that opens in a car stereo. Choose constant 160 kbps and convert. The MP3 will be 36 MB (20,000 bytes per second × 1,800 s). Because the source was already 128 kbps, 160 kbps leaves some headroom; going to 320 kbps would double the size to 72 MB and would not improve the sound.

Limits and common mistakes

Privacy: what the code does

Your files are decoded and re-encoded entirely in this browser tab, using FFmpeg compiled to WebAssembly and the LAME MP3 encoder. The frame that holds the tool has no network access, no advertising and no analytics, so recordings do not go to any server. Nothing remains after you close or reload the page.

Common mix-ups

  1. MDN: Media container formats (file types)
  2. MDN: Web audio codec guide

Checked against these sources on .

Frequently asked questions

What is the difference between AAC and M4A?

AAC is the compression method. M4A is a container that usually holds AAC and adds a header with duration and tags. A raw .aac file is a bare stream of AAC frames.

Why will my .aac file not play on my device?

Many players and libraries expect the MP4 container, not bare ADTS frames. Converting to MP3 gives a file nearly every device opens.

Can I convert .m4a files here too?

Yes. AAC inside .m4a and audio-only .mp4 are accepted. The M4A-specific page adds notes about voice memos and Apple Lossless.

What bitrate should I choose?

At or above the source bitrate, for example 160 or 192 kbps for a 128 kbps AAC source. Speech can go lower, around 64 to 96 kbps.

Is this lossless?

No. AAC and MP3 are both lossy, so you compress twice. Keep the original AAC file.

Why is the source duration only approximate?

A raw .aac file has no duration header, so the engine estimates it from the file size and bitrate. The converted MP3 has the real length.

What if the conversion fails?

The file may be damaged, protected, or wrapped in a stream type the engine cannot read, such as LATM. Check that it plays in a media player, then try again.

Do my files leave my device?

No. The work is done by code in your browser, inside a frame with no network access.

Sources

Standards and documentation behind the claims on this page.

What this tool does not do

It does not remove DRM, read every exotic AAC wrapper, or give you a better recording than the original AAC. Lossy formats (MP3, AAC, Ogg) discard information, so keep your originals.

Advertisement
Advertisement