Print production · geometry
Make the page fit.
Turn a finished trim size into the file canvas and content-safe rectangle. Choose a KDP or commercial starting point, then confirm the final numbers with your printer.
Trim and preset
Layout geometry
Enter a trim size to see the file canvas and safe area.
Geometry is a starting point, not a printer approval
KDP’s published guidance uses 0.125 in (3.2 mm) bleed on the top, bottom, and outside edges of a paperback cover. KDP also says borders should sit at least 0.25 in (6.4 mm) inside the trim line. Commercial printers vary, so the commercial preset is only a transparent starting point.
Privacy: no dimensions leave this browser. This page does not generate a print-ready PDF or account for spine width, imposition, creep, binding, colour profile, or printer-specific tolerances.
Sources checked 29 September 2026: KDP paperback cover requirements and KDP paperback submission guidelines.
Trim, bleed and safe area in one picture
Every printed piece has three nested rectangles. The trim is the finished size after the paper is cut, for example a 6 × 9 inch paperback page. The bleed is extra artwork that extends past the trim so that, when the sheet is cut with a small natural variation, no white sliver appears at the edge. The safe area sits inside the trim and is where you keep text, logos and anything else that must not be cut off or look crowded against the edge. The calculator on this page turns a trim size into the file canvas you export (trim plus bleed) and the content-safe rectangle (trim minus the safe inset).
The arithmetic, edge by edge
File width equals trim width plus the left and right bleed, and file height equals trim height plus the top and bottom bleed. The safe width is trim width minus the left and right safe insets, and the safe height is trim height minus the top and bottom insets. If the insets are larger than the trim, the tool tells you the safe area is bigger than the page instead of returning a negative size. Millimetres are converted at 25.4 mm per inch, so the 0.125 inch bleed is 3.175 mm, which KDP rounds to 3.2 mm.
What each preset does
- KDP paperback interior: 0.125 in bleed on the top, bottom and outside edge and none on the inside (gutter) edge, with a 0.375 in content margin all round. For a 6 × 9 in book the file is 6.125 × 9.25 in and the safe area is 5.25 × 8.25 in. KDP’s guidelines say to format a bleed manuscript 0.25 in higher and 0.125 in wider than the trim size, which is the same result.
- KDP paperback cover panel: 0.125 in bleed around a single panel and a 0.25 in inset. For 6 × 9 in, the panel canvas is 6.25 × 9.25 in and the safe area is 5.5 × 8.5 in. This is a single front or back panel; a full wrap also needs spine width, which the KDP cover calculator works out.
- Commercial print, standard starting point: 0.125 in bleed and 0.125 in safe inset on every edge. For 6 × 9 in, the canvas is 6.25 × 9.25 in and the safe area is 5.75 × 8.75 in. Many commercial printers publish their own figures, and some ask for more, so replace these with the printer’s specification when you have it.
Worked example in millimetres
Suppose you are designing an A5 flyer, 148 × 210 mm, with the commercial preset. Choose millimetres, enter 148 and 210, and the tool converts to inches, adds 0.125 in (3.175 mm) of bleed on each side, and reports a file of about 154.35 × 216.35 mm. The safe area, with a 0.125 in inset on every side, is about 141.65 × 203.65 mm. Set up the document at the larger size, extend backgrounds to the full canvas, and keep headlines inside the safe rectangle.
Interior margins depend on page count
One number does not fit every book. KDP’s margin table asks for a larger inside (gutter) margin as page count grows: at least 0.375 in for 24 to 150 pages, 0.5 in for 151 to 300, 0.625 in for 301 to 500, 0.75 in for 501 to 700 and 0.875 in for 701 to 828 pages. The outside margin must be at least 0.25 in without bleed and 0.375 in with bleed. This calculator’s single 0.375 in inset therefore matches a short book, and a longer book needs a bigger gutter than the tool shows. Always check the table for your page count.
Common mistakes
- Exporting at the trim size and forgetting the bleed, which makes printers reject the file or leaves white edges.
- Putting a thin border near the edge. KDP says it does not recommend borders because of a production variance of about 0.125 in that can trim a border or make it uneven, and that any border should be at least 0.25 in inside the trim line.
- Letting the bleed exceed the allowance: KDP says bleed at the bottom of the page cannot exceed 0.125 in.
- Treating the preset as an approval. Spine width, imposition, creep, binding, colour profile and printer tolerances are outside what a geometry calculator can know.
Once you have a PDF, inspect its boxes with the PDF box checker, and confirm the pixel sizes of placed images with the image DPI checker. All calculation happens in your browser and no dimensions are sent anywhere.
Frequently asked questions
How much bleed do I need for printing?
A common starting point is 0.125 inch (3.2 mm) on each edge that is trimmed, and Amazon KDP requires exactly that for covers and for interiors with images that run to the page edge. Your printer’s template overrides any generic figure.
What is the difference between bleed, trim and safe area?
Trim is the final cut size, bleed is artwork extended beyond the trim to avoid white edges after cutting, and the safe area is the region inside the trim where text and key graphics should stay. The file you export is trim plus bleed.
How do I calculate the file size with bleed from a trim size?
Add the left and right bleed to the trim width and the top and bottom bleed to the trim height. For a 6 × 9 inch page with 0.125 inch bleed on every edge the file is 6.25 × 9.25 inches.
Why is the KDP interior file only 0.125 inch wider than the trim?
KDP interiors need bleed on the top, bottom and outside edges but not on the inside edge next to the binding. That adds 0.125 inch to the width and 0.25 inch to the height.
How far inside the trim should text sit?
It depends on the product. KDP says cover text must be at least 0.125 inch inside the trim lines and any border at least 0.25 inch inside, and interior margins grow with page count. This tool’s presets use more cautious insets than the minimum text rule.
Does this calculator include the spine?
No. It handles one panel or page at a time. A paperback full-wrap cover also needs spine width, which depends on page count and paper, so use a cover calculator for that.
Is the result a print-ready approval?
No. It is geometry only and does not account for imposition, binding, colour profiles or printer tolerances, so confirm the final numbers with your printer or platform before sending files.
Sources and retrieval dates
- Amazon KDP: Paperback cover requirements — 0.125 in (3.2 mm) bleed on the top, bottom and outside edges, 0.125 in text inset, borders and 0.25 in guidance, 300 DPI images (retrieved 2026-10).
- Amazon KDP: Paperback submission guidelines — interior full-bleed sizing, margin table by page count, 0.125 in bleed limit (retrieved 2026-10).
- Amazon KDP: Set trim size, bleed, and margins — definitions of trim size, bleed and margins (retrieved 2026-10).