Candle makers

Candle wax & fragrance oil calculator.

Enter your container size, how full you fill it and the fragrance load you want. You get grams of wax and fragrance oil per candle and for the whole pour.

Fragrance oil weight = wax weight x load %. A candle that weighs 200 g when filled at 8% load holds about 185 g of wax and 15 g of fragrance oil, because the load is measured against the wax alone.

Advertisement

Your numbers

Container and pour
%

Weigh a known volume of your own melted wax for the true figure. Many container waxes are near 0.9; check your supplier.

Fragrance and allowance
%
%

Result

Advertisement

How the amounts are worked out

The tool converts the container to millilitres, multiplies by your fill level and wax density to get the finished fill weight, then splits that weight between wax and fragrance so that fragrance is exactly your chosen percentage of the wax. A pour allowance is added to the totals only.

Fill level matters: filling to the rim wastes wax and leaves no room for a wick trim, so most makers leave some headroom. Your wax supplier states the highest fragrance load that wax is meant to carry, and different waxes differ. Set the load to that guidance, not to a number from a calculator.

To price what you make, continue with the candle cost per candle calculator.

Everything runs in your browser. Nothing you type is sent or stored.

The calculation, step by step

  1. Container volume in millilitres. US fluid ounces are converted at 29.5735 mL per ounce (the NIST SP 811 conversion); millilitres are used as entered.
  2. Finished fill weight = volume × fill level × wax density.
  3. Wax = fill weight ÷ (1 + fragrance load). Fragrance oil is part of the finished weight, so the wax is less than the fill weight.
  4. Fragrance oil = wax × fragrance load.
  5. Totals for the batch = per-candle amounts × number of candles × (1 + allowance for pot and jug loss).

Worked example with the default numbers

Twelve 8 US fl oz containers filled to 90% with wax at 0.9 g/mL and an 8% load. The container is 8 × 29.5735 = 236.6 mL. The finished fill is 236.6 × 0.90 × 0.9 = 191.6 g. Wax is 191.6 ÷ 1.08 = 177.4 g (6.26 oz) and fragrance oil is 177.4 × 0.08 = 14.2 g. For twelve candles with a 5% pour allowance, you need 2,235.8 g of wax and 178.9 g of fragrance oil.

Why the load is a percentage of the wax, not the whole candle

By the common candle-making convention, fragrance load is measured against the weight of the wax. For a 200 g finished candle at 8%, taking 8% of 200 g (16 g) would give too much oil, because the wax is only about 185 g and 8% of that is 14.8 g. The difference looks small, but it is about 8% more oil than you intended in every candle. Some suppliers quote loads differently, so confirm which basis your supplier uses.

Fragrance oil per pound of wax

Many makers work from a pound of wax. One pound is 16 oz, or about 453.6 g, so the fragrance oil you add at common loads is:

LoadOil per 16 oz of waxGrams
6%0.96 oz27.2 g
8%1.28 oz36.3 g
10%1.60 oz45.4 g
12%1.92 oz54.4 g

Weigh both the wax and the oil on a scale. Volume is a poor measure because oils differ in density from supplier to supplier, and this calculator works in weight for that reason. The same arithmetic applies to any scented product made by weight, such as wax melts or body butter, but the safe load for a skin product is a different question from a candle, so use your supplier’s guidance for each.

Choosing the load, and why this tool does not choose it for you

The maximum load depends on the wax, the fragrance and the wick. The National Candle Association says fragrance addition should be carefully monitored so that a candle burns cleanly and properly. Your wax supplier’s data sheet states the recommended maximum for that wax, so use that figure or lower, and test-burn each combination before selling it. Fragrance safety is separate again: the IFRA Standards set the maximum dose of certain fragrance ingredients in finished consumer goods, and your fragrance supplier should tell you which category your candle falls into and whether your load complies. The same applies to essential oils: follow your supplier’s documentation.

Common mistakes

Once you know the amounts, price them with the candle cost per candle calculator. For a different container or batch size, change the capacity and number of candles; every other figure scales automatically. Nothing here is safety or health advice.

FAQ

How do I calculate fragrance oil for candles?

Multiply the weight of the wax by the fragrance load percentage. For 500 g of wax at 8%, that is 40 g of fragrance oil. This tool does it from your container size so you do not have to weigh first.

What fragrance load should I use?

Use the maximum your wax supplier states for that wax, or less. The right level depends on the wax and the fragrance, so this calculator leaves the percentage to you.

Is the load a percentage of wax or of the whole candle?

By common candle-making convention it is a percentage of the wax weight. Some suppliers quote it differently, so check which basis yours uses.

How much fragrance oil per pound of wax?

Multiply 16 oz (about 453.6 g) of wax by the load: 0.96 oz at 6%, 1.28 oz at 8%, 1.6 oz at 10% and 1.92 oz at 12%. Weigh the oil; do not measure it by volume.

How much wax do I need for my containers?

Multiply container volume by fill level and wax density to get the finished weight, then divide by 1 plus the load. For twelve 8 fl oz containers at 90% fill, 0.9 g/mL and 8% load, you need about 2,236 g of wax with a 5% pour allowance.

Why should I weigh fragrance oil instead of measuring it?

Loads are percentages of weight, and oils differ in density by supplier, so a measure by volume can put in more or less than you intend. A scale gives the same load every time.

Can I use this for wax melts or other products?

The wax-and-fragrance arithmetic is the same if you make the product by weight, but safe fragrance levels differ by product type and are set by your suppliers and by safety standards such as IFRA. Use your supplier's guidance for each product.

What is a pot and jug loss allowance?

It is the share of wax and oil you lose to the melting pot, pouring jug and spills. The default is 5%. Weigh your batches and adjust it so you buy the right amount.

Sources

Retrieved October 2026. Where a source blocks automated checks this is noted; figures that no source supports are labelled as your own inputs.

Advertisement