Construction · masonry
Concrete block & mortar calculator.
Estimate nominal block count and mortar volume from wall dimensions, openings, block size, joint allowance, and bag yield.
Wall inputs
Masonry estimate
Nominal block planning
The calculator adds a 10 mm metric or ⅜ in customary joint to the block face for the count, subtracts the exact block volume from the net wall volume, and then applies mortar waste. Bag yields vary widely by product; enter the yield printed on the bag or supplied by the manufacturer.
How the block count and mortar volume are calculated
The calculator works from the net wall face. Net area is wall length × wall height minus the openings you enter. Each block in the wall occupies its face plus one mortar joint, so the footprint of one block is (block length + joint) × (block height + joint). The joint is fixed at 10 mm, or 3/8 in in customary units. The block count is net area ÷ that footprint, multiplied by one plus your block waste, rounded up.
Mortar is found by volume. The gross wall volume is net area × block width. The calculator subtracts the exact volume of the blocks (block count before waste × length × height × width), and what remains is joint mortar. Your mortar waste percentage is added, and the total is divided by the bag yield you enter, rounded up to whole bags. Because the answer depends on bag yield, the tool does not guess it: read the yield (in cubic feet or litres) from the bag you plan to buy.
Enter actual block sizes, not nominal ones
This matters more than any other input. In the US a block called 8×8×16 is nominally 16 in long and 8 in wide, and its actual dimensions are 3/8 in smaller so that a 3/8 in joint brings it back to the nominal size. The calculator adds the joint for you, so if you enter the nominal 16 × 8 face, the joint is counted twice and the block count comes out low.
Here is the same wall both ways. The wall is 20 ft long and 8 ft high with 32 sq ft of openings, giving 128 sq ft net, with 5% block waste, 10% mortar waste and a 0.5 cu ft bag.
- Nominal sizes entered (16 × 8 × 8 in): footprint = 16.375 × 8.375 in = 0.952 sq ft; 128 ÷ 0.952 = 134.4 blocks; with 5% waste = 142 blocks.
- Actual sizes entered (15.625 × 7.625 × 7.625 in): footprint = 16 × 8 in = 0.889 sq ft; 128 ÷ 0.889 = 144 blocks; with 5% waste = 152 blocks.
The 10-block difference is a full 7% on a small wall. Both runs report about 0.23 cu yd (6.2 cu ft) of mortar, which is 13 bags at a 0.5 cu ft yield. As a quick check, 20 ft is 15 blocks per course, 8 ft is 12 courses of 8 in, and 15 × 12 = 180 blocks gross. Take away 32 sq ft of openings (32 ÷ 0.889 = 36 blocks) and you are at 144 before waste, which matches the actual-size answer.
Choosing the waste and bag-yield inputs
Block waste of 5% covers breakage and cuts on a simple straight wall. Corners, jambs, bond beams and many openings use half blocks and special shapes, so a wall with lots of detail may need more. For mortar, the default of 10% is the tool's, not a standard. The Brick Industry Association's estimating guide, written for brick masonry, suggests adding 15 to 25% to net mortar quantities, and that is a reasonable range to consider for block too, because joints are never perfectly consistent and mortar is lost on the board and in the mixer. Raise the mortar waste field if you would rather finish with a spare bag than stop to buy one.
Bag yield varies with the product, the water added and whether it is masonry cement, Type N or S mortar mix. A 0.5 cu ft value is a placeholder; replace it with the number printed on your bags. In metric mode the yield is in litres (1 cu ft is about 28.3 L).
Common mistakes
- Counting the joint twice by entering nominal block faces, as shown above.
- Entering the wall height as a number that is not a multiple of the course height. A 9 ft wall with 8 in courses is 13.5 courses; you will need a cut course or a taller wall. The calculator averages the area and will not warn you.
- Subtracting openings that are not masonry, or forgetting lintel blocks, bond-beam blocks and sill units above and below windows.
- Assuming mortar covers the block cores. The result is joint mortar only.
- Mixing wall thicknesses. The width field sets the volume of mortar per joint run; a 6 in or 12 in block needs its own width.
What this calculator does not cover
It does not include grout for reinforced cells (cells holding rebar must be grouted so the bars bond to the wall), vertical or horizontal steel, lintels, footings, ties, flashing or control joints. It does not model face-shell bedding versus full bedding, and it does not size a retaining wall or any wall that carries load. Those walls need an engineered design for reinforcement, footings and connections. For the footing, use the spread footing size calculator and the concrete calculator; for a modular layout, the concrete block wall module planner; and for clay brick, the brick calculator.
Frequently asked questions
How many concrete blocks do I need per square foot of wall?
A standard 16 by 8 inch (nominal) block covers 128 square inches, or 0.889 square feet, of wall face including its mortar joint. That is about 1.125 blocks per square foot, or roughly 112 to 113 blocks per 100 square feet, before waste.
How do I calculate how many blocks a wall needs?
Multiply wall length by wall height, subtract openings, and divide by the area of one block face plus its joint. Add a waste allowance of about 5 percent and round up. The calculator does this for you and also gives mortar volume and bag count.
Should I enter nominal or actual block dimensions?
Enter actual dimensions. The calculator adds a 3/8 inch (10 mm) joint to each block, and a nominal 16 by 8 inch block already includes that joint. Entering nominal sizes counted the joint twice and gave 142 blocks for a 128 square foot wall, while actual sizes of 15.625 by 7.625 inches gave 152.
How many bags of mortar do I need for concrete block?
Divide the total mortar volume by the volume one bag makes. For a 128 square foot net wall the tool estimates about 6.2 cubic feet of mortar, which is 13 bags if each bag yields 0.5 cubic feet. Bag yields differ, so enter the figure printed on your product.
How much waste should I allow for blocks and mortar?
Five percent is a common block allowance for a plain wall, and more is sensible for walls with many corners and openings. For mortar the tool defaults to 10 percent; the Brick Industry Association suggests adding 15 to 25 percent to net mortar quantities for brick, so consider a higher figure if you do not want to run short.
Does this include grout, rebar and the footing?
No. It estimates joint mortar and block count only. Cells that hold rebar must be grouted, and grout, steel, lintels and footings are separate quantities that depend on the wall design.
Where do I find the mortar bag yield?
On the bag or the manufacturer data sheet, usually given in cubic feet or litres of mortar per bag. Yield changes with the product and the amount of water, which is why the calculator makes you enter it instead of assuming a number.
Can I use this for a retaining wall or a load-bearing wall?
Use it only for the quantity of blocks and mortar. Load-bearing, reinforced, retaining or tall masonry walls need engineered reinforcement, footing and connection details that this calculator does not provide.
Sources
- Concrete masonry unit (Wikipedia) — US blocks are nominally 16 in by 8 in and actual sizes are 3/8 in smaller to allow for 3/8 in joints; cells with rebar must be grouted (retrieved 2026-10).
- Dimensioning and Estimating Brick Masonry, Technical Note 10 (Brick Industry Association) — mortar waste of 15 to 25 percent and the estimating approach, written for brick masonry (retrieved 2026-10).
- NIST Guide to the SI, Appendix B: Conversion factors — exact foot and yard definitions behind the customary-to-metric conversions (retrieved 2026-10).
Worked example: 20 ft by 8 ft wall with a 32 sq ft opening
Net area = 20 × 8 − 32 = 128 sq ft. With 16 in by 8 in blocks and a 3/8 in joint, one block plus its joint occupies 16.375 × 8.375 = 137.14 sq in, or 0.9524 sq ft. Exact count = 128 ÷ 0.9524 = 134.4 blocks; 5% waste gives 141.1, rounded up to 142 blocks. Wall volume at an 8 in thickness is 128 × 0.6667 = 85.33 cu ft; the blocks themselves occupy 134.4 × 0.5926 = 79.65 cu ft, leaving 5.69 cu ft of joint mortar. Adding 10% waste gives 6.26 cu ft, and at 0.5 cu ft per bag that is 12.5, so buy 13 bags. Figures as of October 26, 2026 (arithmetic checked against the tool defaults).