Winter heating · Furnace sizing

Furnace size: from your heat loss to input Btu.

Enter the design heating load from a Manual J calculation and the AFUE of the furnace you are considering. You get the input rating that delivers that load, and a check of an existing furnace against it.

Manual J load inAFUE adjustedOversize check

Advertisement

Short answer

A furnace is sized to the home's design heating load, not to its floor area. For a load of 40,000 Btu per hour (an example), a 96% AFUE furnace needs an input rating of about 41,667 Btu per hour, because 40,000 / 0.96 = 41,667. An existing 100,000 Btu input furnace at 80% AFUE puts out 80,000 Btu per hour, 2.0 times that load.

Inputs

The heating load from a Manual J calculation, in Btu per hour. Not a floor-area guess.
On the spec sheet. ENERGY STAR sets 95% (South) and 97% (North) minimums for gas furnaces.
On the furnace nameplate.

Result

Enter your numbers.

Advertisement

How this is calculated, with a worked example

The U.S. Department of Energy's Building America fact sheet says the residential sizing procedures recommended for use in the United States are ACCA's Manual J, which calculates the heating and cooling load, and Manual S, which selects equipment once the loads are known. It warns against casual sizing estimates based on home floor area or contractor experience. That is why this calculator has no square-foot field: it starts from a load you already have and handles the one step that is plain arithmetic, converting load to furnace input through AFUE.

Worked example. Design heating load 40,000 Btu per hour (illustrative). The furnace must put 40,000 Btu per hour into the house. A furnace with 96% AFUE converts 96% of its fuel input, so input needed = 40,000 / 0.96 = 41,667 Btu per hour. The same load at 80% AFUE would need 50,000. Existing-furnace check: a furnace with a 100,000 Btu per hour input at 80% AFUE outputs 100,000 x 0.80 = 80,000 Btu per hour, which is 2.0 times a 40,000 Btu per hour load. (AFUE is a seasonal rating, so this is an approximation of output at full fire.)

Why oversizing is not safe. The same DOE fact sheet reports that when equipment is oversized, initial costs are higher, efficiency is reduced, energy costs increase and comfort may be compromised. It adds that oversized systems use more fan power and often show more duct leakage, and that in one large survey nearly 40 percent of contractors said they oversized on purpose. It also notes that as a home's efficiency improves, the recommended size should drop, so insulation and air-sealing work done before replacing a furnace can shrink the furnace you need. Where to get the load number: ask the installer for the Manual J report, not a rule-of-thumb figure.

Constants and sources are current as of 26 October 2026.

Advertisement

Common mix-ups

  1. U.S. DOE Building America: Right-size heating and cooling equipment

Checked against these sources on .

Frequently asked questions

How do I size a furnace for my house?

Have a Manual J load calculation done. DOE's Building America fact sheet names Manual J and Manual S as the recommended U.S. procedures and warns against estimates based on floor area. Then divide the load by the furnace AFUE to get the input rating.

Can I size a furnace by square footage?

DOE advises being wary of casual sizing estimates based on floor area. Insulation, windows, air leakage and climate change the load, so two homes of the same size can need very different furnaces.

What happens if a furnace is too big?

DOE says oversizing raises initial cost, lowers efficiency, increases energy costs and can compromise comfort, and oversized systems use more fan power and often show more duct leakage.

What is AFUE?

ENERGY STAR describes AFUE as the percentage of the heat in the incoming fuel that is converted to space heat instead of being lost. A 96% AFUE furnace turns about 96% of its fuel into heat for the house.

Does insulating first change the furnace size?

Yes. DOE notes that as a home's efficiency is improved, the recommended size of the heating and cooling system should drop, so do the load calculation after planned upgrades.

Sources

Checked

Runs entirely in your browser. Nothing you type is sent or stored.

Not professional advice

This converts a load you provide into an input rating. It is not a Manual J calculation and not a substitute for a licensed contractor's load calculation and equipment selection.