Home Energy · Holidays 2026
Christmas lights circuit load calculator.
Enter the circuit size and your light sets in watts. The tool shows total watts and amps, the 80% continuous limit and how much room is left.
Short answer: A 15 A, 120 V circuit is 1,800 W; for lights that stay on three hours or more, plan on no more than 80% of that, or 1,440 W (12 A), counting everything else on the same circuit. CPSC also says never to string together more than three sets of incandescent lights.
Your circuit and lights
Result
Enter your details and press Calculate.
Why a circuit has a limit lower than its breaker size
A breaker labelled 15 A trips at 15 amps, but the National Electrical Code does not let you plan to run it that hard for hours. Section 210.20(A) says that where a branch circuit supplies a continuous load, the overcurrent device must be rated for the non-continuous load plus 125 percent of the continuous load. A continuous load is one expected to run three hours or more, and a string of lights left on all evening qualifies. Flip the 125 percent around and the usable share is 80 percent: 12 A on a 15 A circuit, 16 A on a 20 A circuit. At 120 volts that is 1,440 W and 1,920 W.
Everything else on the same breaker counts toward that limit too, which is why the tool has a field for other load: the 1,440 W is shared, not yours alone.
What CPSC says about strings of lights
The Consumer Product Safety Commission's holiday safety page says to never string together more than three sets of incandescent lights and never overload electrical outlets. Its wording is about incandescent sets, so the tool only raises the three-set warning when you pick incandescent. The electrical-safety group ESFI repeats the same three-string limit and adds that overloaded outlets can overheat and start a fire.
Worked example
Four incandescent sets at 40 W plus two sets at 100 W add up to 4 × 40 + 2 × 100 = 360 W. On a 15 A, 120 V circuit that is 3 A, which is 25% of the 1,440 W limit and leaves 1,080 W of room, or about 27 more sets of the 40 W kind. Now plug in 30 sets at 50 W: 1,500 W is 12.5 A, above the 1,440 W limit by 60 W, so that run belongs on two circuits.
Sources and how this is calculated
Total watts = sets × watts per set, summed across the three rows, plus other load. Amps = watts ÷ 120. Limit = breaker amps × 120 × 0.8. Retrieved October 26, 2026. The wording of NEC 210.20(A) used here is the long-standing rule as reproduced in NFPA's 2025-cycle code-panel working draft; the adopted code in your area and your electrician decide what is required in your home. This page does not cover wire gauge or GFCI requirements for outdoor outlets.
Common mix-ups
-
Often assumedIf the plugs fit into the outlet, the outlet can take them.
What the source saysCPSC tells shoppers to never overload electrical outlets. A plug that fits says nothing about how many watts the circuit behind it can carry, which is why the load has to be added up from the tags. [1]
-
Often assumedThe three-set limit is a rule about every kind of light.
What the source saysCPSC words the limit for incandescent lights: never string together more than three sets of them. Its separate warning about overloading outlets applies to any decoration on the circuit. [1]
Checked against these sources on .
Frequently asked questions
How many Christmas lights can I plug into one outlet?
It depends on watts, not on how many strands. Add the watts on each tag and keep the total at or below 1,440 W for a 15 A circuit or 1,920 W for a 20 A circuit, counting everything else on that breaker.
Why 80 percent?
The NEC sizes a circuit for a continuous load at 125 percent of that load. Lights that run three hours or more are continuous, and 1 divided by 1.25 is 80 percent.
How many incandescent strands can I connect end to end?
CPSC says never to string together more than three sets of incandescent lights. Follow any lower limit printed on the packaging or tag.
Does the three-set rule apply to LED lights?
CPSC wording covers incandescent sets. LED sets draw far less power, but each set has its own maximum run printed on the tag, and the circuit limit still applies.
How do I find the watts for a set?
Look at the tag by the plug. If it lists amps, multiply by 120 to get watts. If it lists neither, do not guess: use a set that is labelled.
Does this check the extension cord?
No. Cord gauge and length have their own limits, which the extension cord gauge calculator on this site covers.
Planning aid, not an electrical inspection
Use the tags on your own light sets and follow the manufacturer instructions. A licensed electrician should answer questions about your wiring.