United Kingdom · Number plates
UK number plate size and spacing checker.
Measure your plate in millimetres, enter what you find, and see each figure against the Road Vehicles (Display of Registration Marks) Regulations 2001.
The standard figures: a plate for a vehicle registered after 1 September 2001 has characters 79 mm high and 50 mm wide, a 14 mm stroke, 11 mm between characters, 33 mm between the two groups and 11 mm margins. Motorcycle figures are different.
Your measurements (mm)
Result
Enter at least one measurement and press Check.
What the Regulations require
The Road Vehicles (Display of Registration Marks) Regulations 2001 set the size, shape and spacing of the characters on a UK number plate. Regulation 14 says each character must be 79 millimetres high, except on motorcycles, tricycles, quadricycles, agricultural machines, works trucks and road rollers, where each character may be 64 millimetres high. Table B in Schedule 3 then gives the other dimensions for each height. For plates on vehicles first registered on or after 1 September 2001, and for new plates fitted from that date, the characters must also be in the prescribed font shown in Schedule 4.
The checker compares what you measured with Table B, row by row, and shows the range the Regulations allow. Regulation 12(2) is the tolerance rule: a character height is treated as correct if it is within 1 millimetre of the prescribed figure, and any other dimension is correct if it is within 0.5 millimetres. The margin is a minimum, so a bigger margin is fine.
| Dimension | 79 mm characters | 64 mm characters |
|---|---|---|
| Character width (not I or 1) | 50 mm | 44 mm |
| Stroke width | 14 mm | 10 mm |
| Space between characters in a group | 11 mm | 10 mm |
| Horizontal space between groups | 33 mm | 30 mm |
| Vertical space between groups | 19 mm | 13 mm |
| Minimum margin | 11 mm | 11 mm |
How to measure your plate
Regulation 12(3) fixes how to measure. Horizontal spacing is taken between vertical lines through the outermost edges of the characters or groups, or between that line and the side edge of the plate. Vertical spacing is taken between horizontal lines through the extreme edges of each group, or between that line and the top or bottom edge of the plate. In plain terms: measure from the outside edge of the characters, not the middle of a letter, and measure the margin to the edge of the plate. Use a steel rule or digital caliper and read to the nearest half millimetre.
Worked example
This is a hypothetical rear plate, not a real vehicle. A one-line plate for a car registered in 2023 measures 80 mm character height, 49.5 mm width, 14 mm stroke, 12 mm between characters, 33 mm between the two groups and a smallest margin of 10 mm. Height is within 1 mm (78 to 80 mm allowed), width is within 0.5 mm of 50 mm, stroke is exact, and the group gap is exact. The 12 mm character gap is outside 10.5 to 11.5 mm, and the 10 mm margin falls below the minimum of 10.5 mm once tolerance is applied. The checker reports those two measurements as outside the Regulations and the other four as within.
Layout, colour and supply
Two lines or one? GOV.UK says motorcycles and motor tricycles should have the number on two lines. For cars the horizontal group gap applies on a single-line plate and the vertical gap applies on a two-line plate, so the tool asks for whichever matches your plate. The same GOV.UK page says plates must be reflective, with black characters on a white background at the front and on a yellow background at the rear, no background pattern, the supplier's name and the British Standard number marked on the plate (BS AU 145e for plates fitted after 1 September 2021), and characters that are not removable or reflective. These are not measured by this tool.
Edge cases and common mistakes
- Measuring from the wrong point. Regulation 12(3) measures between lines through the extreme edges of the characters, or from that line to the edge of the plate, so do the same.
- I and 1 are different. Table B gives character width for every character other than the letter I and the figure 1. A narrow I is not a width fault.
- Mixing up the two gaps. Use the within-group gap for neighbouring characters and the group gap for the space between the two halves of the registration.
- Using pre-2001 figures. Older plates, and some replacement plates for older vehicles, follow other columns of Table B. This tool only checks the post-2001 columns.
- Assuming a pass is an MOT pass. The Regulations cover size and layout. GOV.UK separately warns that displaying plates incorrectly can mean a fine of up to £1,000 and a failed MOT.
Who this is for
Drivers who bought plates from a seller and want to check them, owners whose plate was flagged at an MOT, people designing a plate for a custom or show vehicle, and fleet or garage staff who handle replacement plates.
What this does not cover
The tool does not check the prescribed font, colour, reflectivity, the British Standard marking or whether the registration is genuinely yours. It does not cover plates for vehicles first registered before 1 September 2001, the Northern Ireland formats, trailers or the optional flag and symbol rules. It uses the 2001 text as made; GOV.UK's current guidance adds later requirements such as BS AU 145e, and the legislation website shows no outstanding effects on the Table B figures, but check the current rules before you order plates. This is not legal advice or an MOT assessment.
Related: the number plate eye test distance converter uses the same 79 mm by 50 mm characters in its 20 metre rule, and the age identifier decoder explains what the letters and numbers on a plate mean.
Sources
- legislation.gov.uk: The Road Vehicles (Display of Registration Marks) Regulations 2001 (as made, King's Printer PDF)
- legislation.gov.uk: Schedule 3, Layout of registration marks (Table B)
- GOV.UK: Rules for number plates
- GOV.UK: Displaying number plates
Retrieved 20 October 2026. Figures are taken from the Regulations as made on 1 September 2001; the Table B values were checked against the legislation.gov.uk revised page, which shows no outstanding effects. GOV.UK pages show no update date.
Frequently asked questions
What size are UK number plate characters?
For a vehicle registered after 1 September 2001, characters are 79 mm high and 50 mm wide with a 14 mm stroke. On motorcycles, tricycles, quadricycles and some other vehicles they may be 64 mm high and 44 mm wide with a 10 mm stroke.
How much space should there be between number plate characters?
11 mm between characters within a group on a 79 mm plate and 10 mm on a 64 mm plate. The space between the two groups is 33 mm (79 mm plates) or 30 mm (64 mm plates) on a one-line plate.
What is the minimum margin on a number plate?
11 mm between the characters and the top, bottom and side edges of the plate, for both the 79 mm and the 64 mm sizes. The Regulations call it a minimum, so a larger margin is allowed.
Is there a tolerance on number plate measurements?
Yes. Regulation 12(2) treats a character height as correct within 1 mm and any other dimension as correct within 0.5 mm of the prescribed figure.
Does a motorcycle number plate follow different rules?
Yes. GOV.UK says motorcycle and motor tricycle numbers should be on 2 lines, and the Regulations allow 64 mm characters with their own spacing figures. Motorcycles registered on or after 1 September 2001 need a rear plate only.
What colours must a UK number plate be?
GOV.UK says front plates have black characters on a white background and rear plates have black characters on a yellow background, on reflective material with no background pattern.
What is the fine for an illegal number plate?
GOV.UK says displaying plates incorrectly can lead to a fine of up to £1,000 and can also cause your vehicle to fail its MOT.
Can I use a different font on my number plate?
Not on a vehicle first registered on or after 1 September 2001. Regulation 15 requires the characters to be in the prescribed font shown in Schedule 4 of the Regulations.
A measuring aid, not a legal or MOT ruling
This tool compares your measurements with the published 2001 figures. It does not inspect a plate. The enforcing authorities and your MOT tester decide whether a plate complies.