Construction · cabinetry

Cabinet door size & overlay calculator.

Enter the opening and the overlay or reveal you want. Get finished door sizes in fractional inches and a cut list.

Advertisement

Opening and doors

Each line means “door height up to this many inches takes this many hinges.” Copy it from your hinge maker’s chart. Nothing is pre-filled because the rule depends on door weight, material and hinge.

Door size and cut list

Advertisement

How the sizes are calculated

Overlay, reveal and construction type

Overlay is how far the door covers past the edge of the opening; reveal is the visible gap between a door and its neighbour or the frame. Face-frame cabinets have a frame on the front, so the opening is the frame opening and overlay is measured from the frame edge. Frameless (European-style) cabinets have no frame, so the opening is the carcass interior and overlay is measured from the side panel or shelf edge. The arithmetic is the same for both; only where you measure changes. For the overlay a given hinge produces, follow the hinge maker’s data, not a default.

Results are rounded to the nearest fraction you choose, and the decimal value is shown alongside. Confirm the sizes against your hardware, door thickness and shop tolerances, and cut a test door first.

Sources

Formulas: TWC Industrial cabinet door calculator (single overlay, split overlay with 1/8″ center gap, inset with 1/8″ clearance per side), checked September 30, 2026. Overlay and reveal definitions: Blum concealed hinge brochure. Everything runs in your browser and nothing is sent anywhere.

Worked examples with real numbers

Every result is addition and subtraction on the opening you measure, so the quickest way to trust it is to run a few cases by hand.

Single overlay door. Opening 24 in wide by 30 in high, with 1/2 in of overlay on each of the four sides. Width = 24 + 1/2 + 1/2 = 25 in; height = 30 + 1/2 + 1/2 = 31 in. This matches the common retailer rule that a half-inch overlay means adding a full inch to each dimension.

Pair of overlay doors. Opening 30 in wide by 30 in high, 1/2 in overlay, and a 1/8 in gap where the doors meet. Total width covered = 30 + 1/2 + 1/2 = 31 in. Each door = (31 − 1/8) ÷ 2 = 15.4375 in, or 15-7/16 in, and the height is 31 in. Two doors of that size are the cut list; enter more than one identical opening in the quantity box and the cut list multiplies.

Inset door. Opening 18 in wide by 30 in high with a 1/8 in reveal on all four sides. Width = 18 − 1/8 − 1/8 = 17-3/4 in; height = 30 − 1/4 = 29-3/4 in. Inset doors sit inside the opening, so every reveal comes off the size.

Full overlay on a frameless cabinet. A common formula for full overlay is cabinet width minus 1/4 in. If the carcass is 24 in wide with 3/4 in sides, the clear opening is 22.5 in, so to get a door 23-3/4 in wide, enter an overlay of (23.75 − 22.5) ÷ 2 = 5/8 in on the left and right. The calculator has no separate full-overlay mode; this is how to reach the same answer by choosing the overlay that produces your target gap.

Overlay, reveal and gap in plain terms

CabinetNow's guide describes three door styles. A partial (standard) overlay door covers part of the face frame and leaves some of it visible; a half inch per side is the industry-standard partial overlay, though it varies. A full overlay door covers the whole face frame, leaving only a small gap. An inset door sits inside the frame opening, flush with the face, with a narrow reveal around it; the same guide uses 1/8 in on each side for inset doors, which takes 1/4 in off the width and height. In this calculator's “overlay” mode you type how much the door extends past each edge of the opening, and in “inset” mode you type the gap you want left around the door.

The gap between a pair of doors

Two doors that meet in the middle need clearance so they do not rub or bind. The formula published by one door maker subtracts 1/16 in from each door, which leaves a 1/8 in gap, and it explains that this prevents the doors from touching when high humidity makes the wood swell slightly. The calculator defaults the centre gap to 1/8 in for the same reason. Wide gaps look sloppy and very small gaps risk sticking, so this is one setting worth choosing deliberately and then keeping the same across the whole kitchen.

Face-frame or frameless: where to measure

Face-frame cabinets have a frame across the front, so you measure the clear opening inside the frame and the overlay is measured from the frame edge. Frameless cabinets have no frame, so you measure the clear carcass opening between the side panels and top and bottom (or shelves), and the overlay is measured from the panel edge. The arithmetic is identical; what changes is the starting measurement. Measure each opening separately, because cabinet boxes are rarely perfectly square or identical across a run.

Common mistakes

Looking for interior door sizes or rough openings?

This tool sizes cabinet doors and drawer fronts for a given opening. It does not give standard sizes for room doors, and it does not calculate rough openings or door-frame dimensions. For a passage or entry door, take the rough opening and frame measurements from the manufacturer's installation sheet for the exact unit.

What this calculator does not cover

It does not choose hinges: the hinge count comes only from the rule you type, compared with the finished door height, because the right count depends on door weight, material and hinge. It does not drill hinge cups, specify door thickness or stile and rail widths, or account for wood movement across wide panels. Drawer fronts can use the same arithmetic if you enter the drawer opening and the overlay you want. For related shop maths see the board foot cut list calculator, the shelf spacing calculator, the shelf sag calculator, and the wood movement calculator.

Frequently asked questions

How do you calculate cabinet door size for an overlay door?

Measure the opening, then add the overlay on every side you want covered. With a 1/2 inch overlay on all four sides, a 24 by 30 inch opening takes a 25 by 31 inch door. Enter the overlay as the amount per edge, not the total across both sides.

How do I size a pair of cabinet doors?

Work out the total width the pair must cover (opening plus the overlay on each outer edge), subtract the gap where the doors meet, and divide by two. For a 30 inch opening with 1/2 inch overlay and a 1/8 inch gap each door is 15-7/16 inches wide. Height is the same as for a single door.

What is a standard cabinet door overlay?

For partial (standard) overlay doors, a half inch per side is described by CabinetNow as the industry standard, although the amount can vary. Full overlay doors cover the whole frame and inset doors sit inside the opening, so they follow different rules.

How do I size an inset cabinet door?

Subtract the reveal on each side from the opening. With a 1/8 inch reveal all around, the door is 1/4 inch smaller than the opening in both width and height, so an 18 by 30 inch opening takes a 17-3/4 by 29-3/4 inch door.

Do I measure the face frame or the cabinet box?

Measure the clear opening. On a face-frame cabinet that is the opening inside the frame, and on a frameless cabinet it is the opening between the side panels and the top and bottom or shelves. The calculator's arithmetic is the same in both cases.

What gap should I leave between double cabinet doors?

A 1/8 inch centre gap is a common choice, produced by taking 1/16 inch off each door. One door maker explains that this prevents the doors touching when humidity makes them swell slightly. The calculator defaults to 1/8 inch and lets you change it.

How many hinges does a cabinet door need?

The calculator does not assume a number. Type a rule such as "40 = 2" from your hinge maker's chart (door height up to that many inches takes that many hinges) and it applies the rule to the finished door height. The right count depends on door weight, material and the hinge.

Can I use the calculator for drawer fronts or room doors?

You can use it for drawer fronts by entering the drawer opening and the overlay or reveal you want. It does not calculate room door sizes or rough openings, which should come from the door manufacturer's specification for the exact unit.

Additional sources checked

The page's original sources (the TWC Industrial calculator and the Blum concealed-hinge brochure) are listed above; at the time of this review they could not be loaded from our check, so the two guides here independently confirm the same overlay and inset arithmetic.

Advertisement